If you've ever stared at a pick and place machine at 3 a.m., watching an error code slowly eat into your night shift's output, you already know what this article is about. If you haven't — good. Stay anyway. This might keep it that way.

I've been handling SMT equipment sourcing orders for 6 years. During that time I've personally made (and documented) 4 significant mistakes, totaling roughly $87,000 in wasted budget. Now I maintain our team's checklist so nobody else has to repeat them. Today I'm going to walk through the most expensive one: our 2022 decision to buy a refurbished pick and place machine that looked like a $62,000 win on paper.

This isn't a hit piece on used equipment. It's a straight comparison. I'll put new pick and place machines and refurbished or used pick and place machines side by side across four dimensions — purchase price, total cost of ownership, downtime risk and parts availability, and lead time plus ramp-up. Every dimension gets a clear verdict. At least one of them probably won't match your intuition.

Dimension 1: Purchase Price — Used Wins (on Paper)

Let's start with the obvious number, because that's where most buyers start.

A new mid-range automatic pick and place machine runs somewhere in the ballpark of $150,000 to $400,000 depending on the brand, the number of nozzles, and the feeder configuration. That's a wide range because "mid-range" is a wide word.

A used one — same general class, three to six years old — prices between $30,000 and $100,000. On the face of it, that's a 60–75% saving.

That's how we looked at it. We planned out "the savings" before we'd even finalized the model — new feeders, a spare set of nozzles, some tooling. A cheaper PCB pick and place machine with roughly the same spec sheet. Why would anyone hesitate?

But here's the trap. You're comparing a five-year-old machine's current price against a new machine's current price. Those aren't the same thing.

A friend of mine who deals used SMT equipment told me once, "You're not buying the machine. You're buying what it produces for the next five years." I didn't hear him at the time.

Verdict on this dimension: used machines win on purchase price. Whether that win holds is a different question.

Dimension 2: Total Cost of Ownership — Where the Math Flips

This is where it gets uncomfortable.

Our used machine had a sticker price $62,000 lower than the new alternative. Within two years, I watched about half that "saving" get quietly eaten back.

I don't have hard data on industry-wide TCO ratios for refurbished SMT equipment — I wish I'd tracked it more carefully from the beginning. But based on our own invoices and conversations with other buyers, I can reconstruct what actually happened.

On the new side: a new pick and place machine usually comes with a one-to-two-year manufacturer warranty. Installation and initial training are typically bundled. Parts availability is predictable. Technical support exists. There's a clear end-of-life timeline.

On the used side: our machine cost $48,000. The new one would have been $110,000. That's the $62,000 difference. But here's what came after:

  • Refurbishment and hidden repairs: $11,000 for servo motor replacements, air line rework, and a vacuum pump overhaul — none of it in the seller's "reconditioned" report.
  • Engineer training: the older platform was different enough from our current fleet that we sent two technicians off-site. About $6,800 with travel.
  • Production stoppages: roughly 47 hours of unplanned downtime and adjustment in the first six months. The night shift output was unstable that whole quarter. Conservatively, that's about $19,000 in lost throughput.
  • Parts markups: some feeders and nozzle holders were already discontinued and had to come from brokers at 2–3× the new-part price.

Add it up: roughly $37,000 in extra costs. And I'm not even counting the time cost of my team, or the customer-side trust damage from inconsistent delivery windows.

So the real comparison stopped being $48,000 vs $110,000. It became closer to $85,000 vs $110,000. The gap shrank from $62,000 to about $25,000 — and that $25,000 doesn't account for the stress and the stoppage risk you absorb.

Unit price is just the tip of the iceberg. Total cost of ownership includes the purchase price plus setup, training, power, maintenance, spares, downtime, rework, and scrap. The supplier with the lowest unit price often has the highest TCO.

There's a version of this advice that goes, "always get three quotes." That advice ignores the cost of vendor evaluation and the fact that a five-year-old control board carries a completely different risk profile than a new one, regardless of what the quote says.

Verdict: once downtime and hidden repairs are counted, a new automatic pick and place machine is often the cheaper machine over its first three years. Used only wins under specific conditions, which I'll get to.

Dimension 3: Downtime Risk and Parts Availability — Where Used Machines Bleed

The worst part of a used pick and place machine isn't that it breaks. It's that it breaks on its schedule, not yours, and the fix arrives late.

New machines have a defined parts channel. The manufacturer or authorized distributor stocks the part. The catalog lists it. The lead time is visible. You might wait a few days, but you know where it is.

Used machines? That's a lottery.

In Q1 2023, one of our placement heads failed a driver board. That one failure took the line down for almost three days while I called four distributors and two parts brokers. Nobody had the board. We finally sourced a pulled part from an overseas seller (should mention: it cleared customs, eventually). Six extra days.

That single outage cost us around $14,000 in lost production.

I'm not saying every used machine will fail. Some — properly reconditioned by reputable shops — run fine for years. But if you haven't checked the refurbishment report and the spares market, you're rolling dice. And the roll lands when it hurts most.

Here's the pre-check list I use now before any used equipment purchase:

  1. Ask for a critical spares list first — nozzles, feeders, driver boards, vacuum pumps. Confirm what's discontinued and get current lead times.
  2. Ask for the platform end-of-life date. If the OEM has already stopped supporting it, plan accordingly.
  3. Check for proprietary control boards that only exist as pull-outs.
  4. Pay for an independent inspection. Not the seller's own "refurbishment report."

Verdict: on parts availability and long-term serviceability, new machines win clearly. Used can work — but only if you've done the homework on what happens when it stops.

Dimension 4: Lead Time and Production Ramp-Up — The Hidden Cost Nobody Talks About

This is the dimension we completely ignored, and it hurt.

New pick and place machines ship in 6–12 weeks depending on the manufacturer and configuration. That sounds slow. But it includes factory acceptance testing, standard installation, calibration, and a startup that's matched to the boards you actually run.

Used machines look fast. The unit's already in a warehouse. It ships in a week. But once it lands, the real ramp-up begins:

  • Your team installs it — or pays an independent engineer, whose schedule you don't control.
  • The software version on older platforms is often very different from what your current operators know.
  • Your actual component mix may require nozzle changes or head reconfigurations.
  • Nozzle compatibility, feeder pitch, and calibration drift all add small interruptions that are individually minor and collectively exhausting.

Our used machine took close to 7 weeks from delivery to stable production. An equivalent new machine, with OEM startup support, would have been 2–3 weeks.

Those extra 4 weeks, at our order volume, were worth roughly $38,000 in unbuilt boards. Nobody put that number in front of us beforehand.

I should add that manual or semi-manual assembly isn't automatically"worse." Different operations, different constraints. The issue is that sellers always tell you when the machine "ships." They rarely tell you when it "runs."

Verdict: on lead time consistency and ramp-up speed, new wins. The only thing used machines win here is delivery speed — which isn't the same thing as time-to-production.

So When Should You Actually Buy New, and When Used?

I'm not going to tell you "never buy used." We bought a second used machine later and it ran fine. The call depends on your situation. Here's the framework I use now:

Consider used or refurbished if:

  • Budget is tight and this is a secondary line, not your bottleneck.
  • You have an in-house engineer who knows the platform, or verified access to third-party support.
  • You've confirmed critical spares and lead times before signing.
  • You can live with a few weeks of degraded efficiency during ramp-up.

Go new if:

  • This is a core line — one day of downtime has real cost.
  • You're running high-volume, tight-deadline orders with no buffer.
  • Your engineering team doesn't have spare bandwidth for a science project.
  • You need stable OEM service, training, and long-term parts supply.

If you do go used, put the refurbishment certification, spares inventory commitment, service response time, and a ramp-up deadline into the contract. Don't negotiate the price sheet alone.

Trust me on this one: a machine that's $60,000 cheaper on the quote but eats $40,000 of hidden costs and adds two months of instability is not cheaper. That's just a bad deal with a good-looking sticker.

I don't know if every operation tracks this the same way. But from ours — six years, four mistakes, one $87,000 lesson — the cheapest machine has almost never been the cheapest outcome.

Prices and lead times shift. The numbers above are what we tracked between 2022 and 2024, plus ballpark ranges from peers. Verify current market conditions before you commit to either path.